Kit Adjuster Belt Bass For Accordion, Diato

Description

Kit Adjuster Belt Bass For Accordion, Diato
The description of this item has been automatically translated. If you have any questions, please feel free to contact us.
Left hand belt adjustment kit for accordion
in nickel-plated steel, with screws and rivets.
To be able to adjust the belt (strap, thong, sling) of the bass accordions which are devoid of adjustment dial ...
Another article almost untraceable (apart from the manufacturers) ... and yet, what a pleasure to be able to adjust your belt with your left hand at will!
Yes, there are accordions, or old ones, or even models for beginners or "rustic" which do not offer the possibility of being able to adjust the strap with the left hand at will, and then, only solution: the screwdriver and the punch ... this is hardly practical!
However, this adjustment system exists, and you can - if you are a minimum of DIY enthusiasts - install it yourself.
Instructions for use in the form of a "
novel Photo
" sure
https://diato.org/trucs/courr_mg/image001.htm
If you need technical advice, please consult the FAQ as well as the "Tips and Tricks" of my diato site. bzh
Assembly:
First, define the location of the fixed part: you will have to dig a passage for the wheel in the wood.
So above all, below or below the accordion?
On the top, the use is a little more practical, but it is not very aesthetic. Underneath, you can't see it, but it takes a little getting used to at first to adjust your belt.
Once the location has been determined (look at the photo, not at the edge, rather on the bellows side), remove the current belt, screw the plate (pre-holes: 1.5mm forest) and mark the location of the wheel. Unscrew, and dig the wood on about 6 mm, without opening on the other side!
Then re-fix the plate permanently.
On the belt side, now: put the screw in its flange, push it in fully. Present the flange, fully on the strap, and mark the 2 holes to be made to rivet it. Drill the leather to 4 mm with a cookie cutter, then put the bridle and its screw back in place, and place the rivets (female part on the beautiful side of the bridle). Tap the rivets with a hammer.
Here it is, it's almost finished, you just have to insert the screw in its place and screw the knob on it ... for the belt to adjust!
But first you will have to reattach the belt on the other side by adjusting it so that the tension is good (in your hand) for an average adjustment of the mechanics. (Like on the photo)... it is described here:
"tips and tricks"
: Shorten your left hand strap (in pictures)
.
Good luck !
If you need information, consult the FAQ as well as the "Tips and Tricks" of my site
diato. bzh
Rapid dispatch !
Once the location has been determined (look at the photo, not at the edge, rather on the bellows side), remove the current belt, screw the plate (pre-holes: 1.5mm forest) and mark the location of the wheel. Unscrew, and dig the wood on about 6 mm, without opening on the other side! On the belt side, now: put the screw in its flange, push it in fully. Present the flange, fully on the strap, and mark the 2 holes to be made to rivet it. Drill the leather to 4 mm with a cookie cutter, then put the bridle and its screw back in place, and place the rivets (female part on the beautiful side of the bridle). Tap the rivets with a hammer. But first you will have to reattach the belt on the other side by adjusting it so that the tension is good (in your hand) for an average adjustment of the mechanic
Instrument
Accordéon
Matière
Acier nickelé et laiton nickelé
EAN
Non applicable
Marque
Gama Cases
Numéro de pièce fabricant
Kit_reglage_courroie_MG
Type
Accessoire, Pièce
Matériau
acier et laiton nickelé