GDZ93X82-3.5 CNC Air-Cooled Spindle Motor Engraving Milling Grind 220/380V 3.5KW

Description

Ashley Automation
GDZ93X82-3.5 CNC Air-Cooled Spindle Motor Engraving Milling Grind 220/380V 3.5KW
Specification:
Model:GDZ93X82-3.5
Power:  3500W(3.5KW)
Size: 93 * 82mm
Voltage: 220V /380V
Current: 15/8.8A
Frequency: 300Hz
Speed: 0 - 18000rpm
Cooling: Air-Cooled
Collet: ER25
Bearings: 2X7007C P4/2X7002C P4
Grease Lubrication
Net weight: 9kg
1. Electric spindle practices
Electric spindle is a high-speed high-precision components rigidity, we must strictly follow the practices used spindle spindle motor, otherwise it will increase equipment failures, shorten equipment life. Please use the rule as follows:
(1) Before the boot, first ensure that the spindle cooling system to work properly, and then turn the power spindle. Do not use the spindle without the cooling conditions, it is necessary to check the fan and pump are working properly before use. If the spindle is water cooled, to check whether the cooling water containing impurities to ensure water is smooth.
(2) When using electric spindle, spindle from low according to the principle of high speed, gradually increasing speed to warm up, when the spindle load up to speed and smooth operation of the state after the required processing, can better protection spindle, to reduce the wear.
(3) during use is strictly prohibited beat, hit threaded spindle clamp and rotor end, so as not to reduce the component life, affect the results spindles used.
(4) During the operation, the tool must be replaced in the correct way. When the knife, the focus should be uniform, the tool should be aligned with the threaded end of the screw rotor, clamping can be. During operation the tool needs to be replaced before the replacement to wait Spindle cooling, avoid tool change at hot temperature state.
(5) During the operation, if the fixture card spindle rotor end, non-beat way to remove Jigs. Only under the premise of no damage to the rotor shaft threads with pliers and other tools to remove the chuck, and clean the rotor tapered bore and clamp the spindle to avoid Movies shorten life, affecting the quality of workpiece. If the fixture has completely lost precision, it must be replaced immediately.
2. The spindle maintenance specification:
(1) to control the spindle actual time worked. Theoretically prohibit spindle 24 hours of continuous work, operating 12 hours per spindle Spindle let rest at least 2 hours, in order to prevent the formation of shortened due to mechanical fatigue life of the spindle.
(2) to understand the conditions, the ambient temperature and the spindle temperature control. Spindle operating ambient temperature not higher than 35 centigrade degree, when the ambient temperature is above 35 centigrade degree should use air conditioners or other protective measures to reduce the room temperature, thereby reducing spindle temperature.
(3) The spindle cooling water must be kept clean and free of impurities, recommendations to clean up after the end of the spindle shaft waterway, scale and water holes to avoid clogging due to rust. Also, always pay attention to circulating water temperature in the tank, so the water temperature is too high, the cooling effect can not be achieved prefetching.
(4) Always check the power supply connector, to avoid damage to the connector loose or aging brings to the spindle and the drive.
(5) If the downtime to use again, you must tranches from low speed to high speed spindle run-in steps according to the spindle load running, in order to use in the run-through.
(6) during the loading and unloading cutter knife, must tool chuck nut clean.
3. Use Caution
(1) must match the drive spindle chosen correctly according to the electric spindle nameplate good debugging power, voltage and frequency.
(2) Set the frequency converter should be set command channel, and then set the display channel, and finally set the parameters. When setting parameters, be sure that the reference frequency, the frequency of the three highest rated frequency and consistency.
(3) The spindle is generally clockwise in the wrong direction, the drive can change settings or swap any two rotating wire the inverter output UVW terminal on.
(4) In general, water-cooled spindle surface temperature and ambient temperature greater than 20 degrees, the heat can be considered a spindle; when air-cooled spindle surface temperature greater than ambient temperature of 30 degrees, can be identified as the main heat seriously, immediately shut down cooling, a check
4. Maintenance Caution :
(1) Spindle found abnormal sound, should immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.
(2) the operation of an abnormal burning smell, immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.
(3) If the spindle does not run the boot, do not start over, you should carefully check the following related matters: first check the drive parameters to determine the input and output voltage, the spindle parameter settings are correct. Second, check the power cord and wiring connector is plugged in and determine whether the contact connector problem.
(4) Since the electric spindle is a high speed, high rigidity precision components and must therefore be sent back to me by professionals or for repair.
Notice: Because,the international air shipping forbid to ship liquid,powder and batteries, If you purchased goods containing such items, we will not be putting them packing. Thank you for your support.
SALES POLICY:
Your bid is a contract - Place a bid only if you're serious about buying the item. If you are the winning bidder, you will enter into a legally biding contract to purchase the item. If payment is not received within 7 days, item may be offered to the next highest bidder or relisted at the seller's sole discretion.
RETURN POLICY :
We offer 90 days(used) or 180 days(new) free warranty (except consumables).we stand behind every product we sell.If you're not pleased with your purchase, we'll be happy to make an exchange or refund the product price less S&H within 7 days of your purchase. For any exchange or refund, we need the original receipt or a record of the purchase in our system, and the product must be in its original condition, including the box, packaging, and all accessories.Shipping and handling charges are not refundable.
International Buyers:
VAT (Value-Added Tax) is buyer's responsibility. However, we will try our best to minimize it.
About US:
We are professional EBAY sales team and lots of ebay buyers very satisfied with our services.You can enjoy top-quality product and high-quality services from us, Trust me that you will have a pleasant shopping experience in here.
payment :
Shipping :
Click the link above to check out our eBay store.
Best
Customer Service
Prompt
Delivery
100% Money Back
Guarantee
Easy & Secure
Payments
Copyright 2018 Ashley Automation. All rights reserved.